Difference between revisions of "Siemens Gigaset"

From Hackerspace ACKspace
Jump to: navigation, search
(added Targa DIP phone 450 (Gigaset "clone") device. Cleanup small bobs)
(added S675IP and....)
 
(2 intermediate revisions by the same user not shown)
Line 28: Line 28:
 
|Note=
 
|Note=
 
}}
 
}}
 +
 +
Note that '''Settings''' » '''Management''' » '''Reboot & Reset''' doesn't seem to wipe the handsets.  To hard reset, unplug power, press and hold the button while repowering and hold for approximately 15 seconds (it will blink fast).
  
 
The device [https://teamwork.gigaset.com/gigawiki/display/GPPPO/FAQ+Distinctive+Ringing+protocol supports two distinctive rings]; default (extenal) and alert-internal:
 
The device [https://teamwork.gigaset.com/gigawiki/display/GPPPO/FAQ+Distinctive+Ringing+protocol supports two distinctive rings]; default (extenal) and alert-internal:
Line 89: Line 91:
 
|Note=
 
|Note=
 
}}
 
}}
 +
 +
To reset the device, unplug power, press and hold the button while repowering and hold for approximately 5 seconds.
  
 
<onlyinclude>{{#ifeq:{{{transcludesection|connecting_DIP_450}}}|connecting_DIP_450|
 
<onlyinclude>{{#ifeq:{{{transcludesection|connecting_DIP_450}}}|connecting_DIP_450|
Line 121: Line 125:
 
:Also, make sure that under '''Settings''' &raquo; '''Telephony''' &raquo; '''Advanced VoIP settings''', '''SIP port:''' (or its random range) does not conflict with other SIP devices behind the same NAT.
 
:Also, make sure that under '''Settings''' &raquo; '''Telephony''' &raquo; '''Advanced VoIP settings''', '''SIP port:''' (or its random range) does not conflict with other SIP devices behind the same NAT.
 
}}</onlyinclude>
 
}}</onlyinclude>
 +
 +
== S675IP ==
 +
* [https://www.manualslib.com/manual/1076248/Siemens-Gigaset-S675-Ip.html manual]
 +
* Runs on 6.5V (1.2-1.3W)
 +
* supports 6 GAP handsets
 +
* 6 handsets
 +
* 2 simultaneous calls (1 SIP and 1 analog)
 +
 +
{{PoE
 +
|Barrel_plug=unknown
 +
|Barrel_voltage=6.5V
 +
|802:3af_straight=no
 +
|802:3af_crosslink=no
 +
|Legacy_straight=no
 +
|Legacy_crosslink=no
 +
|Compatible_straight=no
 +
|Compatible_crosslink=no
 +
|Unifi_straight=no
 +
|Unifi_crosslink=no
 +
|Note=
 +
}}
 +
 +
To reset the device, unplug power, press and hold the button while repowering and hold for approximately 5 seconds.
 +
 +
<onlyinclude>{{#ifeq:{{{transcludesection|connecting_S675_IP}}}|connecting_S675 IP|
 +
=== connecting the [[Siemens_Gigaset#S675_IP|S675 IP]] ===
 +
 +
Under '''Settings''' &raquo; '''Telephony''' &raquo; '''VoIP''', the following settings are needed:
 +
* '''Connection name or number:''' &lt;anything&gt;
 +
* '''Provider:''' Other provider
 +
* '''Authentication name:''' &lt;username&gt;
 +
* '''Authentication password:''' &lt;password&gt;
 +
* '''Confirm authentication password:''' &lt;password&gt;
 +
* '''Username:''' &lt;username&gt;
 +
* '''Display name:''' &lt;anything&gt;
 +
* '''Lookup Enabled''' (if available, version &ge; 240): yes
 +
* '''Domain:''' ackspace.nl
 +
* '''Proxy server address:''' sip.ackspace.nl
 +
* '''Proxy server port:''' 5060
 +
* '''Registrar server:''' sip.ackspace.nl
 +
* '''Registrar server port:''' 5060
 +
* '''Registration refresh time:''' 110
 +
* '''STUN enabled:''' Yes
 +
* '''STUN server address:''' stun.ekiga.net
 +
* '''STUN server port:''' 3478
 +
* '''STUN refresh time:''' 240
 +
* '''Outbound proxy mode:''' Automatic
 +
* '''Outbound proxy:''' sip.ackspace.nl
 +
* '''Outbound proxy port:''' 5060
 +
* '''Select network protocol:''' Automatic
 +
 +
:Note that these settings might take a while for the Gigaset to connect to the right server (it might indicate an error at first).
 +
:Also, make sure that under '''Settings''' &raquo; '''Telephony''' &raquo; '''Advanced VoIP settings''', '''SIP port:''' (or its random range) does not conflict with other SIP devices behind the same NAT.
 +
}}</onlyinclude>
 +
 +
 +
== N870 IP Pro ==
 +
TBD..
  
 
== notes ==
 
== notes ==
Line 128: Line 190:
 
* every handset needs to be registered to every basestation, so 24 registrations maximum
 
* every handset needs to be registered to every basestation, so 24 registrations maximum
 
* I had some success using an old Profoon PDX-2900:
 
* I had some success using an old Profoon PDX-2900:
−
  * have base station registration activated before entering the PIN
+
** have base station registration activated before entering the PIN
−
  * press and hold ➡️\📞👤 for 3 seconds (🔋 and 🛜 (or 📞👤) will blink)
+
** press and hold ➡️\📞👤 for 3 seconds (🔋 and 🛜 (or 📞👤) will blink)
−
  * press and hold *️⃣🔕 for 3 seconds (it will prompt: <code>bS-_</code>
+
** press and hold *️⃣🔕 for 3 seconds (it will prompt: <code>bS-_</code>
−
  * choose <code>1</code> to <code>4</code> (it will prompt: <code>bS-4 PIN_</code>
+
** choose <code>1</code> to <code>4</code> (it will prompt: <code>bS-4 PIN_</code>
−
  * enter the base station's PIN code
+
** enter the base station's PIN code and finish with 📞
  
  
 
[[Category:Telephony]][[Category:PoE]]
 
[[Category:Telephony]][[Category:PoE]]

Latest revision as of 00:22, 5 January 2025

general info

N510 IP PRO

  • manual
  • Runs on 6.5V (1.2-1.3W)
  • supports 6 GAP handsets
  • 6 handsets
  • up to 4 simultaneous calls
  • Supports IEEE802.3af (PoE)
  • Info Center support (TBD)


Power (over Ethernet) compatibility:
barrel plug: unknown 6.5V

straight crosslink
802.3af yes yes
legacy no no
compatible yes yes
Unifi no no

Note:

Note that Settings » Management » Reboot & Reset doesn't seem to wipe the handsets. To hard reset, unplug power, press and hold the button while repowering and hold for approximately 15 seconds (it will blink fast).

The device supports two distinctive rings; default (extenal) and alert-internal: 

Alert-Info: <http://www.notused.com>;info=alert-internal

Exposed internals:

  • PCB front (where the button goes on top of the led on the center bottom) Blurry image, sorry

  • PCB back

  • Note the clips to open the case

  • Note the pins to open the case

connecting the N510 IP PRO

Under Settings » Telephony » Connection, the following settings are needed:

  • Connection name or number: <anything>
  • Provider: Other provider
  • Authentication name: <username>
  • Authentication password: <password>
  • Username: <username>
  • Display name: <anything>
  • Lookup Enabled (if available, version ≥ 240): yes
  • Domain: ackspace.nl
  • Proxy server address: <leave empty>
  • Proxy server port: <leave empty to trigger SRV lookup>
  • Registration server: <leave empty>
  • Registration server port: <leave empty to trigger SRV lookup>
  • Registration refresh time: 110
  • STUN enabled: Yes
  • STUN server address: stun.ekiga.net
  • STUN server port: 3478
  • STUN refresh time: 240
  • Outbound proxy mode: Automatic
  • Outbound proxy port: <leave empty to trigger SRV lookup>
  • Select network protocol: Automatic
Note that these settings take a while for the Gigaset to connect to the right server (it might indicate an error at first).
Also, make sure that under Settings » Telephony » Advanced VoIP settings, SIP port: (or its random range) does not conflict with other SIP devices behind the same NAT.


Targa DIP phone 450

  • manual
  • Runs on 6.5V (1.2-1.3W)
  • supports 6 GAP handsets
  • 6 handsets
  • 1 simultaneous call


Power (over Ethernet) compatibility:
barrel plug: unknown 6.5V

straight crosslink
802.3af no no
legacy no no
compatible no no
Unifi no no

Note:

To reset the device, unplug power, press and hold the button while repowering and hold for approximately 5 seconds.

connecting the Targa DIP phone 450

SRV does not seem to work, and the port fields are not emptied.

Under Settings » Telephony » VoIP, the following settings are needed:

  • Connection name or number: <anything>
  • Provider: Other provider
  • Authentication name: <username>
  • Authentication password: <password>
  • Confirm authentication password: <password>
  • Username: <username>
  • Display name: <anything>
  • Lookup Enabled (if available, version ≥ 240): yes
  • Domain: ackspace.nl
  • Proxy server address: sip.ackspace.nl
  • Proxy server port: 5060
  • Registrar server: sip.ackspace.nl
  • Registrar server port: 5060
  • Registration refresh time: 110
  • STUN enabled: Yes
  • STUN server address: stun.ekiga.net
  • STUN server port: 3478
  • STUN refresh time: 240
  • Outbound proxy mode: Automatic
  • Outbound proxy: sip.ackspace.nl
  • Outbound proxy port: 5060
  • Select network protocol: Automatic
Note that these settings might take a while for the TARGA to connect to the right server (it might indicate an error at first).
Also, make sure that under Settings » Telephony » Advanced VoIP settings, SIP port: (or its random range) does not conflict with other SIP devices behind the same NAT.

S675IP

  • manual
  • Runs on 6.5V (1.2-1.3W)
  • supports 6 GAP handsets
  • 6 handsets
  • 2 simultaneous calls (1 SIP and 1 analog)


Power (over Ethernet) compatibility:
barrel plug: unknown 6.5V

straight crosslink
802.3af no no
legacy no no
compatible no no
Unifi no no

Note:

To reset the device, unplug power, press and hold the button while repowering and hold for approximately 5 seconds.



N870 IP Pro

TBD..

notes

xopr had a look at the (poor man's) roaming option that is available. In short:

  • you need a "pro" handset that allows multiple base stations (4 is mentioned); when registering to a base station, this option automatically passes by
  • every handset needs to be registered to every basestation, so 24 registrations maximum
  • I had some success using an old Profoon PDX-2900:
    • have base station registration activated before entering the PIN
    • press and hold ➡️\📞👤 for 3 seconds (🔋 and 🛜 (or 📞👤) will blink)
    • press and hold *️⃣🔕 for 3 seconds (it will prompt: bS-_
    • choose 1 to 4 (it will prompt: bS-4 PIN_
    • enter the base station's PIN code and finish with 📞
Retrieved from "https://ackspace.nl/w/index.php?title=Siemens_Gigaset&oldid=9921"